Well, or at least warp time - I've started spinning for the warp for our textile reconstruction. The first bobbin has been spun, and reeled off, and it was quite a bit of yarn... 

The original textile has very, very tightly twisted yarn in the warp, so I've been trying to spin to the same degree of twist without overtwisting it (so that it corkscrews in places). That is a challenge - but, well, I have a few more kilometers to go, and I'll surely get more relaxed about it soon. 

But for now... the weekend is coming, and I'm very much looking forward to that!

I'm fitting a bit of spinning in every day now - and there's noticeable progress. Or, more precisely: The first three bobbins have been filled, and been reeled off, and now I have the first three skeins of yarn, destined to be the weft yarn for our fabric reconstruction. 

They might not look like much, but it's almost 1.5 km of yarn, with a rather high twist (as you can see from the skeins crunching up). A bit more to go for the weft, and then I will go on to spin the warp yarn, from a different kind of wool and with even higher twist. The warp in the original is actually really, really hard-spun, and it will be interesting to reproduce this. I just hope it will behave on the loom and not be too hard and awkward to weave with!

In this case, "it" is the spinning - with the first bobbin all done and completely filled: 

The second bobbin is not full yet, but as soon as it is, I will wind skeins from both of them, measure the amount done, weigh them, and set the twist. And then the rest will be spun.

I'm starting with the weft in this case, and I'm trying to make it a little bit thicker than in the test run; same will happen with the warp. The weft in the originals is rather unevenly thick and thin, so I'm sort of trying to not pay too much attention to thickness while staying in the appropriate range.

It's funny how trying to match a non-perfect original thread is about as hard (though maybe in a different way) than trying to match a really well-done, almost perfect original thread!

Since I've decided to play it safe(r) and do another test run, here's the result of my not-so-perfect weaving:

Yarn twist in the warp is now definitely closer to the original. Also, my selvedges are quite uneven (sadly, that's pretty normal for me) and there's a bit of a weaving mistake at the start (but on the other side of the fabric, so you can't see it here). 

 I have some warp left, so I can do some fun weaving when I feel like it, and maybe improve a little bit... and otherwise, I'll take another closer look at the sample tomorrow and see how well it matches our goal fabric. And then... spinning can more or less start.

A second round of test spinning has happened, and now it's done and the yarns have had their hot bath and are drying, with a bit of weight to keep them stretched. Next step in the adventure will be to activate all my weaving skills and do a little bit of test weaving with the stronger-spun warp yarns, and see how the fibre combination we're planning to use will work. 

You can see the difference in the amount of twist in the two skeins - the grey one is obviously contracting much more than the white one. Fascinating, isn't it? 

Here's the next step in our adventure of fabric reconstructions: Evaluating the tests. 

I've spun the yarns, my partner-in-crime Silvia has done test weaving, and now the samples have been washed (hot! because some like it hot, you know) and it's time to take a close look at them.

First step is to see if the thread count matches - which it does, satisfactorily, in the warp, but it's a bit too low in the weft. Next step is the close-up, and checking to see if thread twist and thread thicknesses, and the overall look of the fabric, matches our goal. 

Which.. well. Let's say there's room for improvement. In this case, the warp yarns can actually have a good bit more twist to match our original fabric; the weft yarns, to me, seem to be okay. Thread thicknesses are within range, too, I'd say.

Now we'll have to decide if we want to do a second sample piece with changed yarn parameters, or if we can gauge the necessary changes well enough to go for the piece proper straight away...

So... things are progressing in that the yarns have been tested, in form of two tiny pieces of fabric, and we're now waiting to see how things look once the test bits are dry again. (Because, as we all know, no textile is ever finished before it's been washed and dried.)

Meanwhile, as opposed to some times in my past, I was smart enough to keep some of the test spun yarns for myself, for future reference, and that is how the storage for them looks: 

Neither of the fibres is, unfortunately, a really good match for the fibres used in the original textile. We're close enough, though, for practical purposes.